Материал: moc8050rev2

Скачать файл

Заказать новую работу

Внимание! Если размещение файла нарушает Ваши авторские права, то обязательно сообщите нам

MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

Order this document by MOC8050/D

GlobalOptoisolator

6-Pin DIP Optoisolators

Darlington Output

(No Base Connection)

The MOC8030 and MOC8050 devices consist of gallium arsenide infrared emitting diodes optically coupled to monolithic silicon photodarlington detectors. The chip to Pin 6 base connection has been eliminated to improve output performance in high noise environments.

They are best suited for use in applications susceptible to high EMI levels.

•No Base Connection for Improved Noise Immunity

•High Collector±Emitter Breakdown Voltage Ð 80 Volts Minimum

•Higher Sensitivity to Low Input Drive Current

•To order devices that are tested and marked per VDE 0884 requirements, the suffix ºVº must be included at end of part number. VDE 0884 is a test option.

Applications

•Appliances, Measuring Instruments

•I/O Interfaces for Computers

•Programmable Controllers

•Portable Electronics

•Interfacing and coupling systems of different potentials and impedance

•Solid State Relays

MAXIMUM RATINGS (TA = 25°C unless otherwise noted)

Rating	Symbol	Value	Unit

INPUT LED

Reverse Voltage	VR	3	Volts
Forward Current Ð Continuous	IF	60	mA
LED Power Dissipation @ TA = 25°C	PD	120	mW
with Negligible Power in Output Detector
Derate above 25°C		1.41	mW/°C

OUTPUT DETECTOR

Collector±Emitter Voltage	VCEO	80	Volts
Collector Current Continuous	IC	150	mA

Emitter±Collector Voltage	VECO	5	Volts
Detector Power Dissipation @ TA = 25°C	PD	150	mW
with Negligible Power in Input LED
Derate above 25°C		1.76	mW/°C

TOTAL DEVICE

Isolation Surge Voltage(1)	VISO	7500	Vac(pk)
(Peak ac Voltage, 60 Hz, 1 sec Duration)

Total Device Power Dissipation @ TA = 25°C	PD	250	mW
Derate above 25°C		2.94	mW/°C

Ambient Operating Temperature Range(2)	T	± 55 to +100	°C
	A
Storage Temperature Range(2)	T	± 55 to +150	°C
	stg
Soldering Temperature (10 sec, 1/16″ from case)	TL	260	°C

1.Isolation surge voltage is an internal device dielectric breakdown rating.

1.For this test, Pins 1 and 2 are common, and Pins 4 and 5 are common.

2.Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.

Preferred devices are Motorola recommended choices for future use and best overall value.

GlobalOptoisolator is a trademark of Motorola, Inc.

MOC8030

[CTR = 300% Min]

MOC8050

[CTR = 500% Min]

Motorola Preferred Devices

STYLE 3 PLASTIC

STANDARD THRU HOLE

CASE 730A±04

SCHEMATIC

1 6

PIN 1. LED ANODE

2.LED CATHODE

3.N.C.

4.EMITTER

5.COLLECTOR

6.N.C.

REV 2

Motorola, Inc. 1995

MOC8030	MOC8050
ELECTRICAL CHARACTERISTICS (T					= 25°C unless otherwise noted)(1)
				A
		Characteristic				Symbol	Min	Typ(1)	Max	Unit
INPUT LED

Reverse Leakage Current						IR	Ð	0.05	10	μA
(VR = 3 V)
Forward Voltage						VF	Ð	1.15	2	Volts
(IF = 10 mA)
Capacitance						C	Ð	18	Ð	pF
(VR = 0 V, f = 1 MHz)
PHOTODARLINGTON (TA = 25°C and IF = 0, unless otherwise noted)
Collector±Emitter Dark Current						ICEO	Ð	Ð	1	μA
(VCE = 60 V)
Collector±Emitter Breakdown Voltage						V(BR)CEO	80	Ð	Ð	Volts
(IC = 1 mA)
Emitter±Collector Breakdown Voltage						V(BR)ECO	5	Ð	Ð	Volts
(IE = 100 μA)
COUPLED (TA = 25°C unless otherwise noted)
Collector Output Current						IC (CTR)(2)				mA (%)
(VCE = 1.5 V, IF = 10 mA)					MOC8030		30 (300)	Ð	Ð
					MOC8050		50 (500)	Ð	Ð

Isolation Surge Voltage(3,4), 60 Hz Peak ac, 5 Second						VISO	7500	Ð	Ð	Vac(pk)
Isolation Resistance(3)						RISO	Ð	1011	Ð	Ohms
(V = 500 V)

Isolation Capacitance(3)						CISO	Ð	0.2	Ð	pF
(V = 0 V, f = 1 MHz)

SWITCHING

Turn±On Time						ton	Ð	3.5	Ð	μs
Turn±Off Time		V	CC	= 10 V, R	= 100 Ω, I = 5 mA(5)	toff	Ð	95	Ð
		V		= 10 V, R	= 100 Ω, I = 5 mA(5)
Rise Time				L	F	tr	Ð	1	Ð
Rise Time						tr	Ð	1	Ð
Fall Time						tf	Ð	2	Ð

1.Always design to the specified minimum/maximum electrical limits (where applicable).

2.Current Transfer Ratio (CTR) = IC/IF x 100%.

3.For this test, LED Pins 1 and 2 are common and Phototransistor Pins 4 and 5 are common.

4.Isolation Surge Voltage, VISO, is an internal device dielectric breakdown rating.

5.For test circuit setup and waveforms, refer to Figure 9.

VF, FORWARD VOLTAGE (VOLTS)

1.8

1.6

1.4

1.2

		TYPICAL CHARACTERISTICS
			(NORMALIZED)	10
				10
PULSE ONLY					NORMALIZED TO: IF = 10 mA
PULSE OR DC					NORMALIZED TO: IF = 10 mA
						TA = 25°C
			CURRENT	1
			CURRENT
°			COLLECTOR		+70°C
TA = ±55°C				0.1	TA = ±55°C THRU
TA = ±55°C					+25°C
25 C	100	1000	OUTPUT		0.5	1	2	5	10	20	50
10	100	1000	OUTPUT		0.5	1	2	5	10	20	50
100°C					+100°C
100°C				0.01
				0.01
			,
IF, LED FORWARD CURRENT (mA)			C			IF, LED INPUT CURRENT (mA)
IF, LED FORWARD CURRENT (mA)			I			IF, LED INPUT CURRENT (mA)

Figure 1. LED Forward Voltage versus Forward Current

Figure 2. Output Current versus Input Current

2	Motorola Optoelectronics Device Data

(mA)CURRENTCOLLECTOR,												(NORMALIZED)CURRENTCOLLECTOR				MOC8030				MOC8050
(mA)CURRENTCOLLECTOR,	140											(NORMALIZED)CURRENTCOLLECTOR	10
	140												10
	120												7
	120					IF = 10 mA							5
	100					IF = 10 mA												NORMALIZED TO TA = 25°C
	100												2					NORMALIZED TO TA = 25°C
													2
	80						5 mA
							5 mA						1
	60												0.7
	40												0.5
	40
C							2 mA					OUTPUT
C	0												0.1
I	0												0.1
	20												0.2
							1 mA
	0	1	2	3	4	5	6	7	8	9	10	,	±60	±40	±20	0	20	40	60	80	100
												C
			VCE, COLLECTOR±EMITTER VOLTAGE (VOLTS)									I		TA, AMBIENT TEMPERATURE (°C)
			VCE, COLLECTOR±EMITTER VOLTAGE (VOLTS)											TA, AMBIENT TEMPERATURE (°C)

Figure 3. Collector Current versus

Figure 4. Output Current versus Ambient Temperature

VCE, COLLECTOR±EMITTER VOLTAGE (NORMALIZED)

			Collector±Emitter Voltage

1.3							NORMALIZED TO TA =				25°C
1.2
1.2
1.1
1.1
1
1
0.9
0.9
0.8
0.8
0.7
0.7

	±60	±40	±20	0	20	40		60	80	100
			TA, AMBIENT TEMPERATURE (°C)

Figure 5. Collector±Emitter Voltage versus Ambient Temperature

(NORMALIZED)	105
CURRENT	104	NORMALIZED TO: VCE = 10 V
CURRENT		NORMALIZED TO: TA = 25°C
DARK	103
DARK
COLLECTOR±EMITTER	102		VCE = 55 V
			30 V
	10
			10 V
	1
	0	20	40	60	80	100
,	0	20	40	60	80	100
CEO			TA, AMBIENT TEMPERATURE (°C)
I

Figure 6. Collector±Emitter Dark Current versus Ambient Temperature

1000

VCC = 10 V

RL = 1000

100

t, TIME (μs)

10					100
10





					10
1
1
0.1	0.2	0.5	1	2	5	10	20	50	100

IF, LED INPUT CURRENT (mA)

Figure 7. Turn±On Switching Times

(Typical Values)

1000
				RL = 1000



100					100
(μs)



TIMEt,
TIMEt,					10
10					10









1								V	CC = 10 V


0.1	0.2	0.5	1		2	5	10	20		50	100
			IF, LED INPUT CURRENT (mA)

Figure 8. Turn±Off Switching Times

(Typical Values)

Motorola Optoelectronics Device Data

MOC8030 MOC8050

TEST CIRCUIT

WAVEFORMS

INPUT PULSE

VCC = 10 V

IF = 5 mA	RL = 100 Ω
IF = 5 mA	10%
	10%
INPUT	OUTPUT	OUTPUT PULSE
	90%
	tr	tf
	ton	t
		off

Figure 9. Switching Time Test Circuit and Waveforms

4	Motorola Optoelectronics Device Data

			MOC8030				MOC8050
		PACKAGE DIMENSIONS
	±A±
			NOTES:
6	4		1. DIMENSIONING AND TOLERANCING PER ANSI
6	4		Y14.5M, 1982.
			Y14.5M, 1982.
	±B±		2. CONTROLLING DIMENSION: INCH.
1	3		3. DIMENSION L TO CENTER OF LEAD WHEN
1	3		FORMED PARALLEL.
				INCHES		MILLIMETERS
F 4 PL	C	L	DIM	MIN	MAX	MIN	MAX
	C		A	0.320	0.350	8.13	8.89
	N		A	0.320	0.350	8.13	8.89
	N		B	0.240	0.260	6.10	6.60
			B	0.240	0.260	6.10	6.60
			C	0.115	0.200	2.93	5.08
			D	0.016	0.020	0.41	0.50
			E	0.040	0.070	1.02	1.77
±T±	K		F	0.010	0.014	0.25	0.36
±T±			G	0.100 BSC		2.54 BSC
SEATING			G	0.100 BSC		2.54 BSC
SEATING			J	0.008	0.012	0.21	0.30
PLANE	G	J 6 PL	K	0.100	0.150	2.54	3.81
		J 6 PL	K	0.100	0.150	2.54	3.81
		0.13 (0.005) M T B M A M	L	0.300 BSC		7.62 BSC
	M		L	0.300 BSC		7.62 BSC
E 6 PL	M		M	0	15	0	15
E 6 PL	D 6 PL		N	0.015	0.100	0.38	2.54
			N	0.015	0.100	0.38	2.54

	0.13 (0.005) M T A	M B M		STYLE 3:
					PIN 1.	ANODE
					2.	CATHODE
					3.	NC
					4.	EMITTER
					5.	COLLECTOR
					6.	NC

CASE 730A±04

ISSUE G

±A±

6	4
	±B± S
1	3
F 4 PL	H	L
	H
	C
	G	J	±T±
	G	J	SEATING
E 6 PL		K 6 PL	PLANE
E 6 PL		K 6 PL
	D 6 PL	0.13 (0.005) M	T B M A M
	0.13 (0.005) M T A M	B M

NOTES:

1.DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2.CONTROLLING DIMENSION: INCH.

	INCHES		MILLIMETERS
DIM	MIN	MAX	MIN	MAX
A	0.320	0.350	8.13	8.89
B	0.240	0.260	6.10	6.60
C	0.115	0.200	2.93	5.08
D	0.016	0.020	0.41	0.50
E	0.040	0.070	1.02	1.77
F	0.010	0.014	0.25	0.36
G	0.100 BSC		2.54 BSC
H	0.020	0.025	0.51	0.63
J	0.008	0.012	0.20	0.30
K	0.006	0.035	0.16	0.88
L	0.320 BSC		8.13 BSC
S	0.332	0.390	8.43	9.90

*Consult factory for leadform

option availability

CASE 730C±04

ISSUE D

Motorola Optoelectronics Device Data

Источник: https://studfile.net/preview/16503601/

Смотрите также:





Изложение содержания дела, по которому приняты судебные постановления
_1-тема-СтрМетал
_1966(~1
_files_materials_5053_prog.ntr
_Антонян Ю.М., Сексуальные преступления. Чикатило и другие
_РГР № 1 (2)