Ä
(3)Disconnect linkage rods from door latch.
(4)Remove screws holding latch to door end frame.
(5)Separate latch from rear door.
Reverse the preceding operation.
(1)Remove rear door trim panel.
(2)Remove silencer pad and water shield.
(3)Remove door frame trim moulding.
(4)Remove screws holding lift plate to door glass.
(5)Loosen glass slam bumpers.
(6)Lift glass upward through opening at top of
door.
Reverse the preceding operation.
Fig. 19 Rear Door
(1)Remove rear door trim panel.
(2)Remove silencer pad and water shield.
(3)Remove bolts holding regulator to inner door panel.
(4)Slide regulator lift arm roller from lift plate channel.
(5)Separate regulator from door.
AY-BODY 23 - 135
Reverse the preceding operation.
(1)Remove rear door glass.
(2)Remove bolts holding upper guide bar mount bracket to inner door panel.
(3)Remove nut holding guide bar to lower door bottom frame.
(4)Slide lift plate channel from regulator roller.
(5)Separate guide bar from door.
Reverse the preceding operation.
REAR DOOR FIXED GLASS OUTER COVERÐAY-S BODY
(1)Remove inner rear door fixed trim bezel.
(2)Remove screws holding fixed glass outer cover to door frame.
(3)Separate cover from door.
Reverse the preceding operation.
Fig. 20 Rear Door Fixed Glass Outer CoverÐAY-S
Body
REAR DOOR OUTER COVERÐAY-P BODY
(1) Remove rear door trim panel and upper frame trim covers.
23 - 136 AY-BODY |
Ä |
|
(2)Remove screws holding rear door outer cover to door upper frame.
(3)Separate outer cover from door.
Reverse the preceding operation.
Fig. 21 Rear Door Outer CoverÐAY-P Body
(1)Remove rear door trim panel.
(2)Remove rear door glass.
(3)Remove screws and bolts holding rear door fixed glass module to door.
(4)Separate fixed glass module from door.
Reverse the preceding operation.
(1)Remove screws holding overhead console to reinforcement bracket.
(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.
(3)Lower console from roof and disconnect wire connectors.
Reverse The preceding operation.
(1) Disconnect battery negative cable.
Fig. 22 Rear Door Fixed Window
Fig. 23 Overhead Console
(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow, if equipped.
(3)Remove screws holding coat hooks to roof above rear doors.
(4)Remove roof rail and A-pillar mouldings.
(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.
(6)Remove overhead console, if equipped.
(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header, if equipped.
Ä
(8)Remove pinch welt holding headlining to sun roof opening, if equipped.
(9)Remove inside rear view mirror from windshield bracket if necessary.
(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining forward about 25 mm (1 in.).
(11)Shift the front of head lining to one side to pull head lining from behind B-pillar trim. Pull head lining from behind other B-pillar trim.
(12)Allow front of head lining to drop downward. Slide head lining forward from behind quarter panel trim.
(13)Remove head lining from vehicle.
Reverse the preceding operation.
Fig. 24 Head LiningÐTypical
(1)Open front door.
(2)Remove screw holding trim panel to cowl, forward of the front door opening.
(3)Remove screws holding scuff plate to door sill.
(4)Separate cowl panel trim and scuff plate from vehicle.
Reverse the preceding operation.
AY-BODY 23 - 137
REAR DOOR OPENING SCUFF PLATE REMOVAL (FIG. 25)
(1)Open rear door.
(2)Remove screws holding scuff plate to door sill.
(3)Separate scuff plate from vehicle.
REAR DOOR OPENING SCUFF PLATE INSTALLATION
Reverse the preceding operation.
A-PILLAR AND ROOF RAIL MOULDINGS
A-PILLAR MOULDING REMOVAL (FIG. 25)
(1)Open front door.
(2)Disengage clips holding A-pillar moulding to roof rail above door opening.
(3)Remove push-in fastener holding lower A-pillar trim to pillar.
(4)Slide A-pillar moulding upward and pull rearward to separate moulding from A-pillar.
A-PILLAR MOULDING INSTALLATION
Reverse the preceding operation.
(1)Open rear door.
(2)Disengage clips holding roof rail moulding to roof rail above rear door opening.
(3)Separate moulding from vehicle.
REAR DOOR ROOF RAIL MOULDING INSTALLATION
Reverse the preceding operation.
B-PILLAR TRIM PANEL
(1)Remove roof rail mouldings and scuff plates as necessary.
(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to B-pillar.
(3)Remove bolt holding seat belt to floor below B-pillar.
(4)Remove screws holding upper B-pillar trim to pillar and separate trim from pillar.
(5)Remove screws holding lower b-pillar trim to pillar and separate trim from pillar.
Reverse the preceding operation.
(1)Remove roof rail mouldings and scuff plates as necessary.
(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to quarter panel.
23 - 138 AY-BODY
(3)Remove rear seat cushion and back.
(4)Remove fastener holding quarter trim to roof
rail.
(5)Remove screws holding quarter trim panel to wheelhouse kickup.
(6)Pull trim panel forward and separate from ve-
hicle.
(7)Remove bolt holding lap belt anchor to floor and push end of belt through access hole in trim panel.
Reverse the preceding operation.
(1)Remove one quarter trim panel.
(2)Remove center high mounted stop lamp cover. Refer to Group 8L, Lamps for instructions.
(3)Disengage clips holding trim to shelf panel and separate trim from vehicle.
Reverse the preceding operation.
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 26)
(1)Remove B-pillar trim panel.
(2)Remove bolt holding seat belt retractor to B-pillar.
(3)Separate retractor from vehicle.
Ä
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 26)
Vehicles equipped with front bucket seats with center console do not have center occupant belts.
(1)Remove bolt holding inboard buckle/center occupant belt to floor.
(2)Disconnect seat belt sensor wire connector.
(3)Separate buckle/belt assembly from vehicle.
INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION
Reverse the preceding operation.
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 27)
(1)Remove quarter trim panel.
(2)Remove bolt holding lap belt to floor at wheelhouse kickup.
(3)Remove bolt holding turning loop to inner quarter panel.
(4)Remove bolt holding seat belt retractor to quarter panel.
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
Fig. 25 Interior Mouldings, Panels, and Trim Covers
Ä
Fig. 26 Front Seat Belts
INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 27)
(1)Remove rear seat cushion.
(2)Remove bolt holding inboard buckle/center occupant belt to floor.
(3)Separate buckle/belt assembly from vehicle.
INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION
Reverse the preceding operation.
AY-BODY 23 - 139
(1)Position seat full forward.
(2)Remove screws holding rear track riser covers and separate covers from tracks.
(3)On power seat track, remove outboard track
cover.
(4)Remove inboard seat belt attaching bolt from
floor.
(5)Remove nuts holding seat track to floor.
(6)Position seat full rearward.
(7)Remove door sill scuff plate and disconnect power seat track wire connector.
(8)Remove bolts holding seat track to cross mem-
ber.
(9)Remove seat from vehicle.
Reverse the preceding operation.
Fig. 28 Manual Front SeatÐTypical
Fig. 29 Power Front SeatÐTypical
Fig. 27 Rear Seat Belts