23 - 120 AP/27 CONVERTIBLE |
Ä |
|
Fig. 19 Door Glass Frame Cap
Fig. 20 Division Channel Bolts
(1)Remove front door glass.
(2)Drill out rivets holding division channel to door frame (Fig. 22).
(3)Separate division channel from stationary glass and remove glass from door (Fig. 23).
(4)Lift division channel upward, out of the door.
(5)Pull the stationary glass weatherstrip from the division channel.
Fig. 21 Front Door Glass
Install the division channel weatherstrip on the stationary glass. Position the glass in the door frame and reverse the removal operation.
Fig. 22 Pop-rivet Removal
(1)Remove stationary glass.
(2)Pull weatherstrip from door frame channel (Fig.
24).
Loosen outside rear view mirror if necessary, and reverse the removal operation.
Ä |
AP/27 CONVERTIBLE 23 - 121 |
|
Fig. 23 Front Door Stationary Glass
Fig. 25 Front Door Glass Rear Channel
Reverse the preceding operation.
Fig. 24 Front Door Stationary Glass Channel Weath-
erstrip
(1)Remove door trim panel.
(2)Raise door glass to full up position.
(3)Remove bolts holding rear channel to inner door panel and door end frame.
(4)Separate channel from door.
Reverse the preceding operation.
FRONT DOOR BELT MOULDING AND WEATHERSTRIP
(1)Remove door glass.
(2)Remove side view mirror.
(3)Remove screws holding belt moulding to outer door panel upper flange.
(4)Separate belt moulding and weatherstrip from
door.
Fig. 26 Front Door Belt Moulding and Weatherstrip
(1)Remove door trim panel.
(2)Remove screws holding guide socket to door end frame.
(3)Separate guide socket from door.
Reverse the preceding operation
23 - 122 AP/27 CONVERTIBLE |
Ä |
|
Fig. 27 Front Door Striker Guide Socket
(1)Remove seat cushion.
(2)Raise sling well behind quarter trim panels to gain access to seat back nuts.
(3)Reach beneath sling well and remove nuts holding seat back to support reinforcement.
(4)Separate seat back from vehicle.
Reverse the preceding operation.
Fig. 28 Rear Seat Attaching Nuts
(1) Remove bolts holding front outboard seat belt to floor. Remove cover from belt end.
(2)Remove screws holding quarter trim to inner quarter panel.
(3)Remove push-in fastener holding top of door opening weatherstrip to quarter trim panel.
(4)Remove door opening sill plate as necessary to clear quarter trim.
(5)Remove courtesy lamp and disconnect wire connector.
(6)Separate trim panel from inner quarter panel and disconnect speaker wire.
(7)Remove bolts holding rear outboard seat belt to inner quarter panel.
(8)Push seat belt end through openings in trim panel and remove trim panel from vehicle.
Reverse the preceding operation.
Fig. 29 Quarter Trim Panel
(1)Remove quarter trim panel as necessary to gain access to striker guide attachments.
(2)Remove nuts holding striker guide to inner quarter panel.
(3)Separate striker guide from lock pillar.
Reverse the preceding operation.
(1)Remove quarter trim panel as necessary to gain access to seat belt retractor.
(2)Remove bolt holding shoulder harness turning loop to inner quarter panel.
(3)Remove bolt holding seat belt retractor to inner quarter panel.
(4)Separate seat belt from vehicle.
Ä |
AP/27 CONVERTIBLE 23 - 123 |
|
Fig. 30 Door Striker Guide
Reverse the preceding operation.
Fig. 31 Front Seat Belt Retractor
(1)Remove quarter trim panel as necessary to gain access to the rear seat belt retractor.
(2)Remove snap-on cover from shoulder harness turning loop.
(3)Remove bolt holding turning loop to rear seat back support reinforcement.
(4)Remove bolt holding retractor to rear seat back support reinforcement.
(5)Separate retractor from vehicle.
Reverse the preceding operation.
Fig. 32 Rear Seat Belt Retractor
(1)Lower convertible top.
(2)Remove quarter trim panel as necessary to gain access to the belt moulding and weatherstrip attaching screws through the opening at the top of the quarter panel.
(3)Remove screws holding moulding to inner quarter panel in quarter glass opening.
(4)Remove nuts holding moulding to quarter panel along top opening.
(5)Raise trunk lid. Remove nut holding moulding to quarter panel from behind quarter panel reinforcement.
(6)Separate quarter panel belt moulding from ve-
hicle.
Apply sealing putty around mounting studs on back of moulding and reverse the removal operation.
23 - 124 AP/27 CONVERTIBLE |
Ä |
|
Fig. 33 Quarter Panel Belt Moulding
(1)Raise trunk lid.
(2)Remove screws holding trunk lid lining to inside of trunk lid.
(3)Support trunk lid in the full up position.
(4)Disconnect trunk lid prop cylinders.
(5)Separate trunk lid lining from vehicle.
Reverse the preceding operation.
Fig. 34 Trunk Lid Lining and Prop Cylinder
(1)Remove trunk lid lining as necessary to gain access to applique attaching nuts.
(2)Remove nuts holding applique to trunk lid.
(3)Separate applique from trunk lid.
(4)Disconnect center high mounted stop lamp wire connector.
(5)Remove applique from vehicle.
Apply sealing putty around mounting studs on back of applique and reverse the removal operation.
Fig. 35 Trunk Lid Applique
(1)Raise trunk lid.
(2)Pull trunk lid opening weatherstrip from pinch flange around opening.
(3)Separate weatherstrip from vehicle.
Position weatherstrip at center of rearward pinch flange. Push weatherstrip onto pinch flange around trunk opening and join the ends of the weatherstrip when they meet.
Fig. 36 Trunk Opening Weatherstrip
(1)Raise trunk lid to full up position.
(2)Disconnect the trunk lamp wire connector, if equipped.
(3)Mark all bolt and hinge attachment locations with a grease pencil to provide reference marks for installation. When installing trunk lid, align all