23 - 78 AJ-BODY
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 14)
(1)Remove quarter trim panel.
(2)Remove bolt holding seat belt retractor to quarter panel.
(3)Separate retractor from vehicle.
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
(1)Remove bolt holding inboard buckle to floor.
(2)Disconnect seat belt sensor wire connector.
(3)Separate buckle assembly from vehicle.
Reverse the preceding operation.
Fig. 14 Front Seat Belts
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 15)
(1)Remove quarter trim panel.
(2)Remove bolt holding lap belt to floor at wheelhouse kickup.
(3)Remove bolt holding seat belt retractor to quarter panel.
Ä
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 15)
(1)Remove rear seat cushion.
(2)Remove bolt holding inboard buckle/center occupant belt to floor.
(3)Separate buckle/belt assembly from vehicle.
INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION
Reverse the preceding operation.
Fig. 15 Rear Seat Belts
(1)Position seat full forward.
(2)Remove screws holding rear track riser covers and separate covers from tracks.
(3)On power seat track, remove outboard track
cover.
(4)Remove nuts holding seat track to floor.
(5)Position seat full rearward.
(6)On power seat track, remove door sill scuff plate and disconnect wire connector.
(7)Remove bolts holding seat track to cross mem-
ber.
(8)Remove seat from vehicle.
Reverse the preceding operation.
Ä |
AJ-BODY 23 - 79 |
|
Fig. 16 Manual Front Seat
Fig. 17 Power Front Seat
(1)Remove bolts holding cushion to floor.
(2)Push center occupant seat belts through openings in cushion.
(3)Remove cushion from vehicle.
Reverse the preceding operation.
(1)Hinge seat back forward and disengage push-in fasteners holding carpet backing to trunk floor.
(2)Remove bolts holding outboard hinge pivot bracket to seat back.
(3)Pull seat back outward to disengage inboard pivot and separate from vehicle.
Reverse the preceding operation.
Fig. 18 Rear Seat Cushion and Back
(1)Position front seats full forward.
(2)Remove rear ash tray.
(3)Remove rear lower carpeted end cover.
(4)Remove nuts holding console to floor bracket.
(5)Position front seats full rearward.
(6)Raise console storage bin cover and remove bottom mat.
(7)Remove screws holding bottom of storage bin to floor bracket.
(8)Remove screws holding console side panels to instrument panel. Disengage hook and loop fasteners and separate side panels from console.
(9)Disconnect shift indicator cable and clip from shift mechanism through right side panel opening, if equipped with automatic transaxle. Refer to Group 8E, Instrument Panel and Gauges for proper service procedures.
(10)Disengage clips holding parking brake lever cover to console and separate cover from vehicle.
(11)Remove center instrument panel bezel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.
(12)Remove screws holding console to lower instrument panel.
(13)Remove bolts holding console to forward floor mounting bracket.
(14)Remove gear selector knob.
(15)Separate console from floor and remove from vehicle.
Reverse the preceding operation.
23 - 80 AJ-BODY
Fig. 19 Center Console
(1)Remove cowl trim panels and scuff plates.
(2)Remove front seats and inboard seat belts.
(3)Remove center arm rest and front console.
(4)Remove outboard seat belt lower attaching
bolts.
(5)Remove left dash panel foot rest.
(6)Remove rear seat cushion.
(7)Pull carpet from under quarter trim covers.
(8)Fold carpet and remove through door opening.
Reverse the preceding operation.
Fig. 20 Floor Carpet and SilencersÐTypical
Ä
(1)Remove screws holding overhead console to reinforcement bracket.
(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.
(3)Lower console from roof and disconnect wire connectors.
Reverse The preceding operation.
Fig. 21 Overhead ConsoleÐTypical
(1)Disconnect battery negative cable.
(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow, if equipped.
(3)Remove screws holding coat hooks to roof above quarter panels.
(4)Remove roof rail and A-pillar mouldings.
(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.
(6)Remove overhead console, if equipped.
(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header, if equipped.
(8)Remove pinch welt holding headlining to sun roof opening, if equipped.
(9)Remove one quarter trim panel as necessary to clear head lining removal path.
(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining from behind quarter panel.
(11)Remove head lining from vehicle.
Ä
Reverse the preceding operation.
(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.
(2)Pull weatherstrip from pinch flange around sun roof opening.
Reverse the preceding operation.
(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.
(2)Disengage snap-on linkage at rear of air deflector in sun roof opening.
(3)Remove screws holding air deflector to front of sun roof opening.
Reverse the preceding operation.
AJ-BODY 23 - 81
(1)Remove head lining as necessary.
(2)Remove A-pillar or quarter trim covers as neces-
sary.
(3)Remove cowl panel and sill plate trim as neces-
sary.
(4)Disconnect effected drain tube from nipple at sun roof opening.
(5)Pull drain tube upward to remove from pillar involved.
Reverse the preceding operation. Route the tube to avoid kinks or puncture from sharp edges.
(1)Remove rear window mouldings.
(2)Remove interior trim as necessary to gain access to rear window defogger wire connector and ground screw, if equipped.
WARNING: WEAR EYE AND HAND PROTECTION WHEN HANDLING SAFETY GLASS. PERSONAL INJURY CAN RESULT.
Fig. 22 Sun Roof
23 - 82 AJ-BODY
CAUTION: Do not damage body or trim finish when cutting out glass or applying fence primer.
(3)Cut the urethane around the perimeter of the back window glass. Refer to Windshield section of this group for proper procedures.
(4)Separate the rear window from the vehicle.
(1)Prepare the work area, window fence, and glass the same way as described in the Windshield section of this group.
(2)Place fence spacers at the locations shown (Fig.
23).
(3)Apply a 10 mm (0.4 in.) bead of urethane around the perimeter of the glass.
(4)Install the glass in the same manner described in the Windshield section of this group.
(5)Install the rear window moulding.
(6)Connect rear window defogger wiring and install interior trim.
(7)After urethane has cured, water test rear window to verify repair. Verify rear window defogger operation, see Group 8N, Rear Window Defogger.
Fig. 23 Rear Window Glass
(1)Raise trunk lid to full up position.
(2)Disconnect the trunk lamp wire connector.
(3)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing trunk lid, align all marks and secure bolts. The trunk lid should be aligned to 4 mm (0.160 in.) gap to the quarter panels and flush across the top surfaces along quarter panels.
(4)Remove the top trunk lid to hinge attaching bolts and loosen the bottom bolts until they can be removed by hand.
Ä
(5) With assistance of a helper at the opposite side of the vehicle to support the trunk lid, remove the bottom trunk lid to hinge attaching bolts. Separate the trunk lid from the vehicle.
Reverse the preceding operation.
Fig. 24 Trunk LidÐTypical
(1)Remove rear parcel shelf trim cover.
(2)Disconnect trunk lid lift torsion bars from hinges.
(3)Mark all attaching bolt, nut, and component locations with a suitable marking device. Use marks as a reference when installing hinge.
(4)Remove bolts holding trunk lid to hinge.
(5)Remove nuts and bolts holding hinge to closure panel below rear window glass.
(6)Separate hinge from vehicle.
Reverse the preceding operation.
(1)Raise and support trunk lid in the full up posi-
tion.
(2)Remove trunk lining as necessary to gain access to torsion bars.
(3)Disengage adjusting end of torsion bar from the slot in the tension adjustment bracket.
(4)Pivot torsion bar out of lift arm swivel.
(5)Disconnect torsion bar from hinge.
Reverse the preceding operation.