Ä |
AG-BODY 23 - 67 |
|
Fig. 36 Quarter Glass Module
(2)Remove head lining as necessary to gain access to inside roof panel.
(3)Remove seal nut holding seam molding to roof panel.
(4)Separate molding from roof panel.
Reverse the preceding operation.
Fig. 37 Roof Seam Molding
(1)Remove access cover from lift gate opening end of quarter panel spoiler.
(2)Remove bolt holding spoiler to tail lamp closure panel.
(3)Remove quarter trim panel.
(4)Remove nuts holding spoiler to quarter panel from behind quarter panel above rear wheelhouse (Fig. 38).
(5)Separate spoiler from vehicle.
Reverse the preceding operation.
Fig. 38 Quarter Panel Spoiler
(1)Raise lift gate to the up position.
(2)Remove nuts holding spoiler to outboard pinch flanges of lift gate.
(3)Separate spoiler from lift gate.
Reverse the preceding operation.
Fig. 39 Lift Gate Spoiler
(1)raise lift gate to the full open position.
(2)Support lift gate on a suitable lifting device.
(3)Remove bolt holding bottom of lift gate prop cylinder to c-pillar.
(4)Remove bolt holding top of lift gate prop cylinder to lift gate.
(5)Separate prop cylinder from vehicle.
Reverse the preceding operation.
23 - 68 AG-BODY
Fig. 40 Lift Gate Prop Cylinder
(1)Raise lift gate to the full open position.
(2)Remove rear roof header molding.
(3)Disconnect lift gate wire connectors and rear window washer hose, if equipped.
(4)Remove upper lift gate trim molding.
(5)Support lift gate on a suitable lifting device.
(6)Disconnect top of prop cylinders from lift gate.
(7)Mark lift gate hinge locations to assist installation an alignment of lift gate.
(8)With assistance of a helper, remove bolts holding lift gate to hinge.
(9)Separate lift gate from vehicle.
Reverse the preceding operation.
Fig. 41 Lift Gate
(1)Raise lift gate to the full open position.
(2)Remove luggage compartment tail trim panel.
(3)Disconnect lock linkage rod from lift gate latch
arm.
(4)Remove nuts holding lift gate latch to tail panel.
Ä
(5) Separate latch from tail panel and disconnect lift gate remote release cable.
LIFT GATE LATCH INSTALLATION
LIFT GATE STRIKER REMOVAL (FIG. 42)
(1)Raise lift gate to the full open position.
(2)Remove lower lift gate trim panel.
(3)Mark lift gate striker location to assist installa-
tion.
(4)Remove bolts holding lift gate striker to lift
gate.
(5)Separate striker from lift gate.
Reverse the preceding operation.
Fig. 42 Lift Gate Latch and Striker
(1)Raise lift gate to the full open position.
(2)Remove luggage compartment tail trim panel.
(3)Disconnect linkage return spring (Fig. 42).
(4)Disconnect linkage rod from lift gate lock arm.
(5)Remove bolts holding lift gate lock to tail panel.
(6)Separate lock from tail panel.
Reverse the preceding operation.
(1)Remove right lower quarter trim panel.
(2)Open fuel fill door.
(3)Remove nuts holding fuel fill door to quarter panel from in luggage compartment.
(4)Separate fuel fill door from vehicle.
Reverse the preceding operation
Ä |
AG-BODY 23 - 69 |
|
Fig. 43 Lift Gate Lock Cylinder
(1)Remove interior trim as necessary to gain access to release cables.
(2)Remove left front door opening scuff plate.
(3)Remove screw holding trim cover to release cable handle and separate cover from handle.
(4)Remove screw holding release handle to door
sill.
(5)Pry open retainer tab holding cable core end in handle pivot. Pry cable case end from handle.
(6)On fuel fill door cable, remove nut holding cable latch to fuel fill opening.
Fig. 44 Fuel Fill Door
(7) On lift gate latch, remove lift gate latch cover and disconnect cable end from latch. Route cable back through trunk lid.
Reverse the preceding operation.
(1)Remove lift gate opening scuff plate.
(2)Remove lift gate opening sill cover.
(3)Remove luggage compartment tail panel trim.
(4)Remove lower quarter trim panels.
(5)Remove bolt holding quarter panel spoiler to tail lamp closure panel, if equipped.
Fig. 45 Lift Gate and Fuel Fill Door Release Cables
23 - 70 AG-BODY
(6)Remove tail lamps and license plate lamps, refer to Group 8L, Lamps for proper procedures.
(7)Remove nuts holding tail lamp closure panel to tail panel.
(8)Remove nuts holding tail lamp closure panel to quarter panel ends.
(9)Separate tail lamp closure panel from vehicle.
Reverse the preceding operation.
Ä
Fig. 46 Tail Lamp Closure Panel
Ä |
AJ-BODY |
23 - 71 |
|||
AJ-VEHICLE BODY COMPONENT SERVICE |
|||||
INDEX |
|||||
page |
page |
||||
A-Pillar and Roof Rail Mouldings . . . . . . . . . . . . |
. 76 |
Outside Door Latch Release Handle . . . . . . . |
. . . . 76 |
||
Cowl Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 73 |
Overhead Console . . . . . . . . . . . . . . . . . . . . |
. . . . 80 |
||
Cowl Panel Trim and Scuff Plates . . . . . . . . . . . . |
. 76 |
Power Door Lock Actuator . . . . . . . . . . . . . . |
. . . . 76 |
||
Door Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 75 |
Quarter Extension Trim Panel . . . . . . . . . . . . . |
. . . 77 |
||
Door Glass Lift Plate and Guide Post . . . . . . . . . |
. 75 |
Quarter Glass Module . . . . . . . . . . . . . . . . . . |
. . . 84 |
||
Door Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 75 |
Quarter Trim Panel . . . . . . . . . . . . . . . . . . . . . |
. . . 76 |
||
Door Trim Panel . . . . . . . . . . . . . . . . . . . . . . . . . |
. 74 |
Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . . |
. . . 78 |
||
Floor Carpet . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 80 |
Rear Seats . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 79 |
||
Front Center Console . . . . . . . . . . . . . . . . . . . . . |
. 79 |
Rear Shelf Trim Panel . . . . . . . . . . . . . . . . . . |
. . . 77 |
||
Front Door and Hinge . . . . . . . . . . . . . . . . . . . . |
. 74 |
Rear Window Glass . . . . . . . . . . . . . . . . . . . . |
. . . 81 |
||
Front Door Silencer and Water Shield . . . . . . . . . |
. 74 |
Sun Roof Air Deflector . . . . . . . . . . . . . . . . . . |
. . . 81 |
||
Front End Splash Shields . . . . . . . . . . . . . . . . . . |
. 73 |
Sun Roof Drain Tubes . . . . . . . . . . . . . . . . . . |
. . . 81 |
||
Front Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . |
. 78 |
Sun Roof Weatherstrip . . . . . . . . . . . . . . . . . . |
. . . 81 |
||
Front Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 78 |
Trunk Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 82 |
||
Fuel Fill Door . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 83 |
Trunk Lid and Fuel Fill Door Release Cables |
. . . . 83 |
||
Glass Run WeatherstripÐAJ-21 Body . . . . . . . . . |
. 76 |
Trunk Lid Hinge . . . . . . . . . . . . . . . . . . . . . . . |
. . . 82 |
||
Grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 71 |
Trunk Lid Latch . . . . . . . . . . . . . . . . . . . . . . . |
. . . 83 |
||
Grille Opening Panel . . . . . . . . . . . . . . . . . . . . . |
. 71 |
Trunk Lid Lock . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 83 |
||
Head Lining . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 80 |
Trunk Lid Luggage Rack . . . . . . . . . . . . . . . . |
. . . 83 |
||
Hood and Hinges . . . . . . . . . . . . . . . . . . . . . . . . |
. 71 |
Trunk Lid Torsion Bar . . . . . . . . . . . . . . . . . . . |
. . . 82 |
||
Hood Latch and Release Cable . . . . . . . . . . . . . |
. 72 |
Trunk Opening Weatherstrip . . . . . . . . . . . . . . |
. . . 83 |
||
Inside Latch Release Handle . . . . . . . . . . . . . . . |
. 76 |
Window Regulator . . . . . . . . . . . . . . . . . . . . . |
. . . 75 |
||
(1)Remove screws holding grille to header at top of grille.
(2)Push downward on top of bumper fascia to gain clearance for grille removal.
(3)Push grille downward and pull outward. Separate grille from vehicle.
Reverse the preceding operation.
Fig. 1 Grille Assembly
(1)Remove front bumper and fascia.
(2)Remove grille and disconnect concealed headlamp motor wire connector.
(3)Remove bolts holding headlamp mounting assemblies to front closure panel.
(4)Remove bolt holding grille opening panel to bracket forward of radiator.
(5)Raise hood and remove push-in fasteners holding sight shields to closure panel. Separate sight shields from vehicle.
(6)Remove nuts holding grille opening panel to front fenders.
(7)Remove bolts holding grille opening panel to front fenders.
(8)Separate grille opening panel form vehicle.
Reverse the preceding operation. Align grille opening panel to fit flush across fender joining locations.
(1)Raise hood to full up position.
(2)Lift front edge of cowl cover on the right side of the windshield washer bottle and disconnect the under hood lamp wire connector.
(3)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to pro-
23 - 72 AJ-BODY |
Ä |
|
vide reference marks for installation. When installing hood, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front fenders and flush across the top surfaces along fenders.
(4)Remove the top hood to hinge attaching bolts and loosen the bottom bolts until they can be removed by hand.
(5)With assistance of a helper at the opposite side of the vehicle to support the hood, remove the bottom hood to hinge attaching bolts. Separate the hood from the vehicle.
Reverse the preceding operation.
Fig. 2 Hood Assembly Remove or InstallÐTypical
(1)Support hood on the side that requires hinge replacement.
(2)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing hood hinge, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front fenders and flush across the top surfaces along fenders. Shims can be added or removed under hood hinge to achieve proper hood height.
(3)Remove hood to hinge attaching bolts.
(4)Remove hood hinge to front fender attaching bolts and separate hinge from vehicle.
Reverse the preceding operation. If necessary, paint new hinge before installation.
Fig. 3 Hood Hinge AssemblyÐTypical
(1)Raise hood to the full up position.
(2)Remove hood latch attaching bolts holding latch to radiator closure panel and separate from vehicle.
(3)Pry release cable casing attachment from slot receiver on latch, disengage cable end from latch arm hook.
Reverse the preceding operation.
(1)Raise hood to the full up position.
(2)Remove push-in fasteners holding hood latch cover to radiator closure panel and separate cover from vehicle.
(3)Disconnect hood release cable casing and cable end from hood latch assembly. Refer to Hood Latch Removal procedure in this section.
(4)Remove hood latch release cable handle attaching bolts from under left lower edge of instrument panel.
(5)Disengage release cable rubber grommet from engine compartment dash panel behind instrument panel.
(6)Rout cable assembly through engine compartment around battery, under fender lip, under relay bank, and under wiring harnesses, toward dash panel. Push cable through access hole in dash panel under the brake master cylinder, into passenger compartment.