23 - 62 AG-BODY |
Ä |
|
(9)Remove screws holding upper quarter trim to quarter panel.
(10)Raise and support lift gate in the up position. Disconnect bottom of lift cylinder.
(11)Swing rear of trim panel away from quarter panel and pull trim forward to clear door opening flange.
(12)Separate upper quarter trim panel from ve-
hicle.
Reverse the preceding operation.
(1)Raise lift gate to the up position.
(2)Remove hidden screws holding tail panel trim cover to tail panel from carpeted area.
(3)Remove push-in fasteners holding top tail panel trim to opening sill.
(4)Lift up floor cover and position cover out of the
way.
(5)Separate cover from vehicle.
Reverse the preceding operation.
(1)Raise the lift to the up position.
(2)Disengage clips holding side moldings to lift gate. Separate moldings from lift gate.
(3)Remove expanding push-in fasteners holding upper trim panel to lift gate.
(4)Remove screw plugs and screws holding upper trim panel to lift gate. Separate upper trim panel from lift gate.
(5)Remove screw plug and screw holding lower trim panel to rear window wiper motor, if equipped.
(6)Remove screws holding lower trim panel to lift gate. Separate lower trim panel from lift gate.
Reverse the preceding operation.
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 26)
(1)Adjust front seat to the forward position.
(2)Remove bolt holding outboard lap belt anchor to floor below door sill.
(3)Remove lower and upper quarter trim panels as necessary to gain access to shoulder harness turning loop and retractor.
(4)Remove bolt holding shoulder turning loop to B-pillar.
Fig. 25 Lift Gate Trim
(5)Remove bolt holding belt retractor to quarter panel.
(6)Separate belt from vehicle.
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
(1)Remove bolt holding inboard buckle to floor.
(2)Disconnect seat belt sensor wire connector, if equipped.
(3)Separate buckle assembly from vehicle.
Reverse the preceding operation.
Fig. 26 Front Seat BeltsÐTypical
Ä
REAR OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 27)
(1)Remove lower and upper quarter trim panel.
(2)Remove bolt holding lap belt anchor to floor at wheelhouse kickup.
(3)Remove bolt holding seat belt retractor to quarter panel.
REAR OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
(1)Lift seat belt buckle anchor cover to expose bolt.
(2)Remove bolt holding inboard buckle/center occupant belt to seat frame.
(3)Separate buckle from vehicle.
Reverse the preceding operation.
Fig. 27 Rear Seat Belts
(1)Position seat full forward.
(2)Remove screws holding rear track riser covers and separate covers from tracks.
(3)On power seat track, remove outboard track
cover.
(4)Remove nuts holding seat track to floor.
(5)Position seat full rearward.
(6)On power seat track, remove door sill scuff plate and disconnect wire connector.
AG-BODY 23 - 63
(7)Remove bolts holding seat track to cross mem-
ber.
(8)Remove seat from vehicle.
Reverse the preceding operation.
Fig. 28 Manual Front Seat
Fig. 29 Power Front Seat
(1)Hinge seat backs forward.
(2)Remove bolts holding rear seat frame to floor on sides of center floor hump near luggage compartment kick-up.
(3)Pull seat forward to disengage retaining hooks from floor.
(4)Separate seat from vehicle.
23 - 64 AG-BODY
Reverse the preceding operation.
Fig. 30 Rear Seat Cushion and Back
(1)Position front seats full forward.
(2)Remove rear ash tray.
(3)Remove rear lower carpeted end cover.
(4)Remove nuts holding console to floor bracket.
(5)Position front seats full rearward.
(6)Raise console storage bin cover and remove bottom mat.
(7)Remove screws holding bottom of storage bin to floor bracket.
(8)Remove screws holding console side panels to instrument panel. Disengage hook and loop fasteners and separate side panels from console.
(9)Disconnect shift indicator cable and clips from shift mechanism through right side panel opening, if equipped with automatic transaxle. Refer to Group 8E, Instrument Panel and Gauges for proper procedures.
(10)Disengage clips holding parking brake lever cover to console and separate cover from vehicle.
(11)Remove center instrument panel bezel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.
(12)Remove screws holding console to lower instrument panel.
(13)Remove bolts holding console to forward floor mounting bracket.
(14)Remove gear selector knob.
(15)Separate console from floor and remove from vehicle.
Reverse the preceding operation.
Ä
Fig. 31 Center Console
(1)Remove cowl trim panels and scuff plates.
(2)Remove front seats and inboard seat belts.
(3)Remove center arm rest and front console.
(4)Remove inboard and outboard seat belt lower attaching bolts.
(5)Remove left dash panel foot rest.
(6)Remove rear seat.
(7)Pull carpet from under quarter trim covers.
(8)Fold carpet and remove through door opening.
Reverse the preceding operation.
Fig. 32 Floor Carpet and SilencersÐTypical
Ä
(1)Remove screws holding overhead console to reinforcement bracket.
(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.
(3)Lower console from roof and disconnect wire connectors.
Reverse The preceding operation.
Fig. 33 Overhead ConsoleÐTypical
(1)Disconnect battery negative cable.
(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow, if equipped.
(3)Remove screws holding coat hooks to roof above quarter panels.
(4)Remove roof rail and A-pillar mouldings.
(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.
(6)Remove overhead console, if equipped.
(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header, if equipped.
(8)Remove pinch welt holding headlining to sun roof opening, if equipped.
(9)Remove screws holding lift gate opening header moulding to rear roof header. Separate moulding from header.
(10)Remove one quarter trim panel as necessary to clear head lining removal path.
(11)Remove head lining from vehicle.
AG-BODY 23 - 65
Reverse the preceding operation.
(1)Remove sunroof glass panel. Refer to Owners manual for proper procedures.
(2)Remove pinch welt holding head lining to edge of sunroof opening.
(3)Remove trim ring from tilt control handle.
(4)Remove screws holding tilt control handle to tilt control. Separate handle from control.
(5)Remove nuts holding lift control to roof panel. Separate lift control from roof.
Reverse the preceding operation.
The rear window moulding often cannot be salvaged after removal operation is completed. Verify moulding availability from the parts supplier before removing moulding.
(1)Remove rear window moulding.
(2)Remove lift gate trim as necessary to gain access to rear window defogger wire connector and ground screw, if equipped.
WARNING: WEAR EYE AND HAND PROTECTION WHEN HANDLING SAFETY GLASS. PERSONAL INJURY CAN RESULT.
CAUTION: Do not damage body or trim finish when cutting out glass or applying fence primer.
(3)Cut the urethane around the perimeter of the back window glass. Refer to Windshield section of this group for proper procedures.
(4)Separate the rear window from the vehicle.
(1)Prepare the work area, window fence, and glass the same way as described in the Windshield section of this group.
(2)Place the fence spacers at the locations shown (Fig. 35).
(3)Apply a 10 mm (0.4 in.) bead of urethane around the perimeter of the glass.
(4)Install the glass in the same manner described in the Windshield section of this group.
(5)Install the rear window moulding. Apply 50 mm (2 in.) masking tape over moulding to assure alignment.
(6)Connect rear window defogger wiring and install lift gate trim.
23 - 66 AG-BODY |
Ä |
|
Fig. 34 Sunroof
(7) After urethane has cured remove masking tape and water test to verify repair. Verify rear window defogger operation, refer to Group 8N, Rear Window Defogger.
(1)Remove quarter trim panel as necessary to gain access to quarter glass module.
(2)Remove nuts holding quarter glass module to quarter glass opening.
(3)Cut urethane bonding around perimeter of quarter glass opening fence.
(4)Push quarter glass module from quarter glass opening.
(5)Separate module from vehicle.
(1)Clean hardened urethane from quarter glass opening fence and glass module, if module replacement is not required.
(2)Prepare fence and module using method described in the Windshield section of this group.
(3)Reverse the removal operation.
(1) Remove upper quarter trim panel.
Fig. 35 Lift Gate Window Glass