Ä
(3)Remove bolt holding seat belt to floor below B-pillar.
(4)Lift B-pillar trim off door opening sill weatherstrips and push inward.
(5)Slide B-pillar trim downward as far as possible and separate trim from B-pillar.
B-PILLAR TRIM PANEL INSTALLATION
Reverse the preceding operation.
(1)Remove roof rail mouldings and scuff plates as necessary.
(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to quarter panel.
(3)Remove rear seat cushion, back, and rear bol-
ster.
(4)Remove push-in fastener holding quarter trim to roof rail.
(5)Remove screws holding quarter trim panel to wheelhouse kickup.
(6)Pull trim panel forward and separate from ve-
hicle.
Reverse the preceding operation.
(1) Remove rear seat cushion, back, and rear bolster.
AA-BODY 23 - 27
(2)Disengage clips holding expansion trim panel to shelf panel.
(3)Separate trim panel from vehicle.
Reverse the preceding operation.
(1)Remove one quarter trim panel.
(2)Remove center high mounted stop lamp cover. Refer to Group 8L, Lamps for instructions.
(3)Disengage frog leg fasteners holding trim to shelf panel and separate trim from vehicle.
Reverse the preceding operation.
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 40)
(1)Remove B-pillar trim panel.
(2)Remove bolt holding seat belt retractor to B-pillar.
(3)Separate retractor from vehicle.
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
Fig. 39 Interior Mouldings, Panels, and Trim Covers
23 - 28 AA-BODY
INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 40)
Vehicles equipped with front bucket seats with center console do not have center occupant belts.
(1)Remove bolt holding inboard buckle/center occupant belt to floor.
(2)Disconnect seat belt sensor wire connector.
(3)Separate buckle/belt assembly from vehicle.
INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION
Reverse the preceding operation.
Fig. 40 Front Seat Belts
OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 41)
(1)Remove quarter trim panel.
(2)Remove bolt holding lap belt to floor at wheelhouse kickup.
(3)Remove bolt holding seat belt retractor to quarter panel.
OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION
Reverse the preceding operation.
INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 41)
(1)Remove rear seat cushion.
(2)Remove bolt holding inboard buckle/center occupant belt to floor.
(3)Separate buckle/belt assembly from vehicle.
Ä
INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION
Reverse the preceding operation.
Fig. 41 Rear Seat Belts
(1)Position seat full forward.
(2)Remove screws holding rear track riser covers and separate covers from tracks.
(3)On power seat track, remove outboard track
cover.
(4)On 50/50 seats, remove inboard seat belt attaching bolt from floor.
(5)Remove nuts holding seat track to floor.
(6)Position seat full rearward.
(7)On power seat track, remove door sill scuff plate and disconnect wire connector.
(8)Remove bolts holding seat track to cross mem-
ber.
(9)Remove seat from vehicle.
Reverse the preceding operation.
(1)Remove bolts holding cushion to floor.
(2)Push center occupant seat belts through openings in cushion.
(3)Remove cushion from vehicle.
Reverse the preceding operation.
Ä
Fig. 42 Manual Front Seat
Fig. 43 Power Front Seat
(1)Hinge seat back forward and disengage push-in fasteners holding carpet backing to trunk floor.
(2)Remove bolts holding outboard hinge pivot bracket to seat back.
(3)Pull seat back outward to disengage inboard pivot and separate from vehicle.
Reverse the preceding operation.
(1)Remove rear seat cushion and back as neces-
sary.
(2)Remove bolts holding outboard back bolster to quarter panel.
(3)Lift bolster upward to disengage hook retainer on back of bolster and separate from vehicle.
AA-BODY 23 - 29
SEAT BACK BOLSTER CUSHION INSTALLATION
Reverse the preceding operation
Fig. 44 Rear Seat Cushion and Back
(1)Position front seats full forward.
(2)Remove access hole plugs on sides of center arm rest riser and remove bolts holding riser to floor bracket.
(3)Remove coin holder and remove screws holding arm rest riser to front console.
(4)Position front seats full rearward.
(5)Remove radio bezel from instrument panel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.
(6)Remove screws holding console to lower instrument panel rail.
(7)Remove screws and disengage hook and loop fastener holding carpet panels to sides of console and separate panels from console.
(8)Remove screws holding console to forward floor mounting bracket.
(9)Remove set screw holding gear selector knob to shift lever and pull knob from shifter on vehicles with automatic transaxle.
(10)Lift forward edge of PRNDL cover and separate cover from console on vehicles with automatic transaxle.
(11)Lift gear shift boot adapter from console and push adapter through opening in console on vehicles with manual transaxle.
(12)Separate console from floor and remove from vehicle.
23 - 30 AA-BODY
Reverse the preceding operation. On vehicles with automatic transaxle, verify gear selector indicator adjustment before returning vehicle to use.
Fig. 45 Front Center Console
(1)Remove cowl trim panels and scuff plates.
(2)Remove front seats and inboard seat belts.
(3)Remove center arm rest and front console.
(4)Remove outboard seat belt lower attaching
bolts.
(5)Remove rear seat cushion.
(6)Pull carpet from under B-pillar trim covers.
(7)Fold carpet and remove through front door opening.
Reverse the preceding operation.
Fig. 46 Floor Carpet and Silencers
Ä
(1)Remove screws holding overhead console to reinforcement bracket.
(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.
(3)Lower console from roof and disconnect wire connectors.
Reverse The preceding operation.
Fig. 47 Overhead Console
(1)Disconnect battery negative cable.
(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow.
(3)Remove screws holding coat hooks to roof above rear doors.
(4)Remove roof rail and A-pillar mouldings.
(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.
(6)Remove overhead console, if equipped.
(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header.
(8)Remove pinch welt holding headlining to sun roof opening, if equipped.
(9)Remove inside rear view mirror from windshield bracket if necessary.
(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining forward about 25 mm (1 in.).
Ä
(11)Shift the front of head lining to one side to pull head lining from behind B-pillar trim. Pull head lining from behind other B-pillar trim.
(12)Allow front of head lining to drop downward. Slide head lining forward from behind quarter panel trim.
(13)Remove head lining from vehicle.
Reverse the preceding operation.
Fig. 48 Head Lining
(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.
(2)Pull weatherstrip from pinch flange around sun roof opening.
Reverse the preceding operation.
(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.
(2)Disengage snap-on linkage at rear of air deflector in sun roof opening.
(3)Remove screws holding air deflector to front of sun roof opening.
Reverse the preceding operation.
AA-BODY 23 - 31
(1)Remove head lining as necessary.
(2)Remove A-pillar or B-pillar trim covers as necessary.
(3)Remove cowl panel and sill plate trim as neces-
sary.
(4)Disconnect effected drain tube from nipple at sun roof opening.
(5)Pull drain tube upward to remove from pillar involved.
Reverse the preceding operation. Route the tube to avoid kinks or puncture from sharp edges.
(1)Remove quarter panel trim covers.
(2)Remove head lining.
(3)Remove nuts holding transverse roof moulding to roof panel and separate moulding from vehicle.
(4)Remove nuts holding vinyl top bonnet to roof.
(5)Remove rear deck filler panel.
(6)Remove screws holding rear window opening lower valance to body.
(7)Disengage hook and loop fasteners holding vinyl top bonnet to quarter panels.
(8)Pull vinyl top bonnet away from top panel to separate bonnet from anti-flutter sealer holding bonnet to roof.
(1)Clean anti-flutter sealer from roof surface and inside of vinyl roof bonnet.
(2)Apply a 20 mm (0.75 in.) bead of anti-flutter sealer across the roof panel at the mid point between the front of the bonnet and rear of roof.
(3)Apply a 20 mm (0.75 in.) by 150 mm (6 in.) bead of anti-flutter sealer down each roof side panel at mid point between the door opening and rear of roof.
(4)Place the bonnet into position on the roof panel and align to proper fit.
(5)Reverse the removal operation.
(1)Raise truck lid to full up position.
(2)Remove screws holding rear deck filler panel to body in the front trunk opening gutter.
(3)Close trunk lid, do not latch.
(4)Lift filler panel upward and separate from ve-
hicle.